點擊圖片放大商品名稱:
規格介紹:
WIKA FLC-HHR-FP
HHR FlowPak® flow meter
規格介紹:WIKA FLC-HHR-FP
HHR FlowPak® flow meter
詳細介紹:
No straight upstream and downstream pipes required
It can also be mounted immediately after two 90° pipe elbows without any problems.
Features:
- • Highest accuracy and energy efficiency
- • No upstream and downstream pipes required
- • Wide range of applications
更多商品
WIKA FLC-OP, FLC-FL, FLC-AC Orifice plate, Orifice flange, Annular chamber
Orifice plates are the simplest type of primary flow elements. Suitable orifice plates are available for a wide range of different media. Orifice flanges feature pairs of pressure tappings which are machined directly into the orifice flange. Annular chambers are used to achieve stable measurements under difficult process conditions. Features: • Max. operating temperature and pressure limited by material and flange • Suitable for liquid, gas and steam flow measurement • Accuracy ≤ ±0.5 % of actual flow rate • Repeatability of measurement of 0.1 %
WIKA FLC-MP Multi-hole orifice plate
The model FLC-MP requires only 2 diameters downstream and 2 diameters upstream. This enhances the accuracy of flow measurement and minimises disturbances in flow, offering the orifice plates offer high performance even in short upstream and downstream pipes. Features: • For requirements in short straight up- and downstreampipes • Suitable for liquid, gas and steam flow measurement • Compact version available • Accuracy 1 % ... 2 % depending on beta ratio andReynolds number • Repeatability 0.1 % of flow rate
WIKA FLC-MR Meter run / meter tube
Differential pressure flow meters are used in many industrial applications. Features: • Max. operating temperature and pressure limited by material and rating • Suitable for liquid, gas and steam flow measurement • Accuracy ≤ ±1.0 % of actual flow rate • Repeatability of measurement 0.1 %
WIKA FLC-FN-PIP, FLC-FN-FLN, FLC-FN-VN Venturi nozzle, Flow nozzle
It can be used in a wide variety of applications that include steam, air, water, vapour, gas, chemical substances and high temperatures. For applications with erosive media a hardened internal surface is available. Features: • Suitable for liquid, gas and steam flow measurement • Optimum solution for measuring the flow of steam • Accuracy ≤ ±0.1 % of actual flow rate • Repeatability of measurement 0.1 % • Lowest pressure loss in the family of primary flow elements
WIKA FLC-VT-BAR, FLC-VT-WS Venturi tube
The main advantages of a Venturi tube over other differential pressure flow meters are the higher pressure recovery and the lower upstream and downstream pipe requirements. Features: • Suitable for liquid, gas and steam flow measurement • Accuracy ≤ ±0.5 % of actual flow rate • Repeatability of measurement 0.1 % • Lowest pressure loss in the family of primary flow elements • Calibration may be performed if required
WIKA FLC-APT-E, FLC-APT-F Pitot tube
The pitot tube is suitable for the measurement of one-phase media which completely fill the cross-section of the pipe. The nominal sizes range from 50 ... 1,800 mm (2" ... 72"), the pipe schedule is specified by the customer. Features: • Suitable for liquid, gas and steam flow measurement • Accuracy ≤ ±2 % of actual flow rate • Repeatability of measurement 0.1 % • Ensure the lowest pressure loss in the family of primary flow elements (approx. < 1 %)
WIKA FLC-RO-ST, FLC-RO-MS Restriction orifice
Our technical department will evaluate the correct design for the restriction orifice, depending on customer requirements and flow conditions. Features: • Suitable for liquid, gas, and steam applications • Single and multi bore solutions • Multi-step executions
WIKA FLC-FC Cone flow meter
The model FLC-FC cone flow meter uses differential pressure to determine the flow in applications with limited mounting space. Features: • Suitable for liquids, gases and steam • Wide turndown • Low requirements for straight upstream and downstream pipes • Low costs and low maintenance effort
